Haier dehumidifier troubleshooting

Haier dehumidifier troubleshooting. Hair dehumidifier troubleshooting can be difficult. If this method didn’t work, some common dehumidifier problems may include leaking water, excessive noise, or a fan that isn’t working.

These issues are often easier to fix than you think, but you still have to follow the right steps if you want to get them fixed properly.

Haier dehumidifier troubleshooting

haier dehumidifier troubleshooting

In this post, we’ll go through a short troubleshooting guide for your Haier dehumidifier that will help you figure out what is wrong with the unit and how to fix the problem.

This guide was designed to be applied to any of these particular dehumidifiers, so hopefully, it can help you find some solutions for whatever issues you may be experiencing right now.

Haier Dehumidifier does not work

The bucket switch opens when the water bucket is full to turn off the dehumidifier. If a defect occurs in this part, it will prevent the dehumidifier from operating.

To determine if this part is defective, use a multimeter to test for continuity after removing each wire harness connector one at a time from the bucket switch until no connectors remain.

If each test reveals no continuity and thus confirms that the bucket switch has failed to operate, replace it with a new one.

Haier dehumidifier freezes

Testing to see if your dehumidifier fan is spinning freely is as easy as turning the blade with your hand.

Never pull on the fan blade, since this could damage the motor. Note any obstructions you find on or around the blades.

If you find an obstruction, simply remove it from the area so that air can pass over the coils more easily.

Dehumidifiers are often used in basements where dirt, dust, and grime tend to collect within that environment. No one wants a dirty house.

So keep an eye out for obstructions such as spiderwebs or other debris when cleaning.

If you think your dehumidifier may be too cold because of a clogged air filter, allow time for it to be repaired before replacing any parts (such as coils/evaporator assembly).

You may also consider purchasing and installing another unit that is already clean and ready to use in its place while waiting for the repair process to be finished.

Haier Dehumidifier fan won’t work

First, try turning the fan blade by hand. If the fan blade is stiff or does not turn easily, it might be bound up with some dust and debris.

Carefully remove whatever is binding the fan from rotating properly and then continue to check if it turns freely.

This is vital as you don’t want your project’s success to falter because of a simple little thing like this! Make sure that the fan blade is not rubbing against the fan housing while spinning.

If all seems well here, try using a multimeter to ensure whether or not there is power coming into your project’s motor.

Once all of these checks have been made, we’re able to confidently assume that either your dehumidifier’s motor or temperature sensor has taken it upon themselves to cease working for no apparent reason and therefore need a replacement immediately.

Haier Dehumidifier water leaks

It’s possible that the bucket might be cracked or positioned incorrectly. Use your binoculars to make sure that the bucket is positioned in such a way as to not let water leak and also make sure it hasn’t been cracked open, which would mean water can easily escape.

Feel around the hose fittings to make sure they aren’t damaged in any way, you should then check the seal to ensure that it’s not broken.

Haier Dehumidifier makes a lot of noise

Turn the fan by hand. If you have to force it, there could be something stopping it from turning easily. This is bad as they are supposed to be smooth and not barely able to turn.

The parts that most commonly cause this problem are a build-up of lint or other debris in the airways,

an assembly not installed correctly on the motor shaft, a broken blade or worn bearings on the fan itself, or friction between other moving parts like a worn belt, poor pulley alignment, or bent axle.

Check for all of these and replace whatever wasn’t meant to be there or is causing problems. Also, apply your own method of cleaning everything out.

Otherwise, if you don’t it will lead back to the same problem later on and cost more money when it does.

Otherwise, if everything was fine but still sounds loud make sure that there isn’t anything wrong with the compressor doesn’t even cover half the cost of getting a new one so next time check if it was that before buying one.

Related Guides